Scope of Work (SOW):
-
All spaces where demolition by Contractor occurs to be repainted and finished to match existing.
-
All new lights to be LED.
-
Furniture removal/relocation by Contractor.
-
Hazardous materials testing by Owner.
1. New Booking Room:
-
Remove Existing VCT and Cove Base and Install New VCT and 4" Cove Base in booking room.
-
Furnish & Install new Transition Strip at Door Entry for Flooring
-
Cut, Modify, Frame Opening, and Patch Drywall for 3’tall x3’ wide new tempered one-way glass window in storefront frame (black in color and installed 48" AFF).
-
Remove residential metal screen door, fill holes in HM Frame, prep/paint Existing Frame.
-
Remove all cabinets and booking chairs
-
Remove & Dispose of 3 Wood benches that are currently anchored to floor.
-
Remove & Salvage Booking Chair that is currently anchored to floor.
-
Remove & Replace and/or Fix Existing 16”wide x20” Tall Access Panel
-
New plastic laminate countertop with backsplash and counter supports – 24” deep x 10’ wide (Corner to Corner) (countertop will have to be notched Around Wall Bump-outs at each corner.
-
Tape bed and texture all repairs and provide new paint at Entire Room.(Existing Wood Door to Remain as is)
2. New Holding Room:
-
Remove existing holding room wood door and Hollow Metal Frame.
-
Modify Existing Framing as Needed for New Hollow Metal Frame
-
New 3’x7’ Hollow Metal Door and Frame for holding room complete with Detention Hardware per attached specs. New Hollow metal Door to be half glass with tempered one-way glass window. Door to be also equipped with a pass-thru detention hardware.
-
Prep & Paint New Hollow metal Frame and Door to Match Existing Frames and Doors in Facility
-
Prep & Paint Exterior Wall where new Hollow metal frame will be installed – 36’ wide x 8’ tall (Match existing color as close as possible)
-
Remove Existing carpet tile and 4” cove base.
-
New standard epoxy floor and 4” base in holding room. (Existing is carpet tile so floor needs to be properly prepped)
-
Furnish & Install new Transition Strip at Door Entry for Flooring
-
New holding benches and rails anchored to structure. Quantity 2 - Lengths 1- at 4’ and 1 at 3’ - see attached specs
-
Remove Existing 2’x2’ Acoustical ceiling grid and tile.
-
Fur down new Ceiling and provide new drywall ceiling, textured, and painted to match existing walls.
-
Remove Existing Lay-in Lighting (2) and replace with flush mounted fixtures for drywall ceiling. Lighting to be IBC metal covered, tamper proof as required. New Lighting to be 1 – 2’x4’ LED flush mount light.
-
Relocate Existing Light Fixture switch outside of room in hall adjacent to new hollow metal frame.
-
All existing outlets in holding room shall be blanked off with stainless steel cover plates with tamper proof screws.
-
Remove Existing HVAC lay in grilles and provide new surface mounted diffusers - 1-12”x12” supply air grille and 1-12”x12” return air grille
-
Tape bed and texture all repairs and provide new paint at Entire Room.
3. Exterior Booking Door
-
Remove existing exterior booking door and provide new insulated 3’x7’ hollow metal frame to fit in existing frame.
-
Fill holes in existing HM Frame
-
Prep & Paint existing Hollow metal Frame and new hollow metal Door to Match Existing Frames and Doors in Facility
-
Furnish and install the following hardware for new door in existing frame:
-
Closer
-
Panic Bar that will work with Existing Card Reader
-
Remount Existing Card Reader Controls
-
Threshold, Weatherstripping, Kickplate, and Door Sweep
-
Drip Cap for Top of Door
-
Heavy Duty Hinges
-
Pull handle or Similar for Exterior Access Controlled by Card Reader
4. Common Hallway Exiting Admin Area
-
Remove and Swap Doors in Corridor and Hallway
-
Change and Swap Out Locks Only
-
Remove & Replace Existing Glass with new tempered one-way glass window – 6” wide x 30” tall (Existing vision lite is held in door with wood trim – this is to be removed)
-
Furnish and Install new vision lite frame for new one-way glass window
-
Existing Finishes on Wood Doors and Hollow Metal Frames to Remain as is
5. Private Bathroom Door
-
Re-use Existing wood door and install new vision lite frame with new tempered one-way glass window – 6” wide x 30” tall
-
Existing Finish on Wood Door and Hollow Metal Frame to Remain as is
6. Interior Electrical
-
Back up battery system for emergency lighting and lay-in lighting/ballasts thru out admin area for safety egress
-
Back up battery system for keypad access and cameras - NIC done by Others
-
Holding Room Camera - NIC done by Others
-
Booking Door Camera - NIC done by Others
-
Hallway Camera - NIC done by Others
7. Exterior Electrical
-
Ensure the light angles are to code.
-
Entire exterior building lighting automated with timer and/or photocell
-
Remove and Replace building mounted flagpole light fixture with new LED fixture.
-
Remove & Replace all Existing Wall Packs (5) with New LED Wall packs - see attached specs.
-
Add Two (2) New LED Wall packs, both on west side of building (1 in fenced area) - see attached specs.
-
Existing Automatic gate operator replacement. – Remove & Replace with Similar Model – See attached Existing pictures. Existing Concrete Pad for Operator is 24”x36”x4” thick. Existing gate is chain-link with 3 strands of barbwire. (Gate Dimensions are 32’ wide x 7’3” tall)
-
Furnish and install new exit loop and 12-volt and/or 24-volt battery backup
-
New Operator must be compatible for card reader access to be done by others.
-
Fix and Ensure Electrical to Gate Operator is sealed and properly terminated.
8. New Ramp and Stairs for Booking Intake at Rear Entry
-
Remove & Replace Existing concrete sidewalk from new ADA ramp past Existing Exterior Booking Door (Existing is Settling) - Make sure concrete is replaced from joint to joint.
-
ADA Concrete ramp with painted railing to access existing parking lot.
-
New Concrete stairs with painted railing adjacent to New ADA Concrete ramp.
-
Remove and Dispose of Existing Concrete and gravel.
-
Cut and Demo Existing Slump Block wall inside of fence area down to existing exterior slab to prevent people from jumping fence into impound area.
-
Furnish and Install metal plate at existing chain-link fence to prevent intrusion into fenced area once slump block wall is removed. Weld in place, prep, and paint.
9. New Asphalt
-
Demo of existing asphalt as required (check slope).
-
New 2” asphalt over 4” base course near booking and for 90% parking. See attached google earth image
-
Leave unfinished space for onsite impound.
-
Slope to unfinished area for ponding
-
Remove and Demo Small Tree in Fence on West Side of Building and Fix Barbed Wire at top of Fence
-
Stripe new Asphalt Areas to Maximize spots and to accommodate ADA ramp and existing concrete
New Fencing. Electrical, Gate Operator, Etc.
Overview: The State Police Station requires enclosure of portion of private existing lot to increase security of personnel and vehicles.
-
New 6’ Tall Basic Commercial Fence with 3-strands of bar wire for a 7’3” overall rough height at Rear Entry- See attached google earth image
-
All fence posts to be core drilled thru existing asphalt and set on concrete
-
Furnish and Install one new 16’ manual vehicle gate on north side of property
-
Furnish and Install one new 4’ manual man gate on north side of building
-
Furnish and Install one new 26’ automatic vehicle gate on west side of property, complete with gate operator, exit loop, 12-volt and/or 24-volt battery backup
-
New Operator must be compatible for card reader access to be done by others.
-
Electrical to be from existing gate operator to be replaced above on existing fence.
-
Saw-cut, remove, and Replace Asphalt for New Electrical and Exit Loop for new Gate operator
-
Saw-cut and remove asphalt at automatic gate for new 12” wide x 12” deep concrete ribbon to be installed under sliding gate roller.
-
Saw-cut and remove asphalt at automatic gate operator for new concrete pad to be installed under operator
-
Remove & Replace Concrete pad at existing gate operator so electrical sub can properly tie in new gate operator power as required.
-
Furnish and install 4” painted bollards at sliding gate and around new gate operator – approx. 3’ in ground and 5’ out of ground - 15 bollards required
-
The following items are to remain in place if this alternate is accepted:
-
Cut and Demo Existing Slump Block wall inside of fence area down to existing exterior slab to prevent people from jumping fence into impound area.